Please wait, while we are loading the content...
Please wait, while we are loading the content...
| Content Provider | The American Society of Mechanical Engineers (ASME) Digital Collection |
|---|---|
| Author | Haldeman, Charles Dunn, Michael Mathison, Randall Troha, William Hoek, Timothy Vander Riahi, Ardeshir |
| Copyright Year | 2012 |
| Abstract | A detailed aero performance measurement program utilizing fully cooled engine hardware (high-pressure turbine stage) supplied by Honeywell Aerospace Advanced Technology Engines is described. The primary focus of this work was obtaining relevant aerodynamic data for a small turbine stage operating at a variety of conditions, including changes in operating conditions, geometry, and cooling parameters. The work extraction and the overall stage performance for each of these conditions can be determined using the measured acceleration rate of the turbine disk, the previously measured moment of inertia of the rotating system, and the mass flow through the turbine stage. Measurements were performed for two different values of tip/shroud clearance and two different blade tip configurations. The vane and blade cooling mass flow could be adjusted independently and set to any desired value including totally off. A wide range of stage pressure ratios, coolant to freestream temperature ratios, and corrected speeds were used during the course of the investigation. A combustor emulator controlled the free stream inlet gas temperature, enabling variation of the temperature ratios and investigation of their effects on aero performance. The influence of tip/shroud gap is clearly seen in this experiment. Improvements in specific work and efficiency achieved by reducing the tip/shroud clearance depend upon the specific values of stage pressure ratio and corrected speed. The maximum change of 3% to 4% occurs at a stage pressure ratio and corrected speed greater than the initial design point intent. The specific work extraction and efficiency for two different blade tip sets (one damaged from a rub and one original) were compared in detail. In general, the tip damage only had a very small effect on the work extraction for comparable conditions. The specific work extraction and efficiency were influenced by the presence of cooling gas and by the temperature of the cooling gas relative to the free stream gas temperature and the metal temperature. These same parameters were influenced by the magnitude of the vane inlet gas total temperature relative to the vane metal temperature and the coolant gas temperature. |
| Sponsorship | International Gas Turbine Institute |
| Starting Page | 765 |
| Ending Page | 776 |
| Page Count | 12 |
| File Format | |
| ISBN | 9780791844700 |
| DOI | 10.1115/GT2012-69941 |
| Volume Number | Volume 4: Heat Transfer, Parts A and B |
| Conference Proceedings | ASME Turbo Expo 2012: Turbine Technical Conference and Exposition |
| Language | English |
| Publisher Date | 2012-06-11 |
| Publisher Place | Copenhagen, Denmark |
| Access Restriction | Subscribed |
| Subject Keyword | Temperature Cooling Inertia (mechanics) Blades Metals Clearances (engineering) Pressure Flow (dynamics) Engines Aerospace industry Design Geometry High pressure (physics) Coolants Disks Hardware Combustion chambers Damage Turbines |
| Content Type | Text |
| Resource Type | Article |
National Digital Library of India (NDLI) is a virtual repository of learning resources which is not just a repository with search/browse facilities but provides a host of services for the learner community. It is sponsored and mentored by Ministry of Education, Government of India, through its National Mission on Education through Information and Communication Technology (NMEICT). Filtered and federated searching is employed to facilitate focused searching so that learners can find the right resource with least effort and in minimum time. NDLI provides user group-specific services such as Examination Preparatory for School and College students and job aspirants. Services for Researchers and general learners are also provided. NDLI is designed to hold content of any language and provides interface support for 10 most widely used Indian languages. It is built to provide support for all academic levels including researchers and life-long learners, all disciplines, all popular forms of access devices and differently-abled learners. It is designed to enable people to learn and prepare from best practices from all over the world and to facilitate researchers to perform inter-linked exploration from multiple sources. It is developed, operated and maintained from Indian Institute of Technology Kharagpur.
Learn more about this project from here.
NDLI is a conglomeration of freely available or institutionally contributed or donated or publisher managed contents. Almost all these contents are hosted and accessed from respective sources. The responsibility for authenticity, relevance, completeness, accuracy, reliability and suitability of these contents rests with the respective organization and NDLI has no responsibility or liability for these. Every effort is made to keep the NDLI portal up and running smoothly unless there are some unavoidable technical issues.
Ministry of Education, through its National Mission on Education through Information and Communication Technology (NMEICT), has sponsored and funded the National Digital Library of India (NDLI) project.
| Sl. | Authority | Responsibilities | Communication Details |
|---|---|---|---|
| 1 | Ministry of Education (GoI), Department of Higher Education |
Sanctioning Authority | https://www.education.gov.in/ict-initiatives |
| 2 | Indian Institute of Technology Kharagpur | Host Institute of the Project: The host institute of the project is responsible for providing infrastructure support and hosting the project | https://www.iitkgp.ac.in |
| 3 | National Digital Library of India Office, Indian Institute of Technology Kharagpur | The administrative and infrastructural headquarters of the project | Dr. B. Sutradhar bsutra@ndl.gov.in |
| 4 | Project PI / Joint PI | Principal Investigator and Joint Principal Investigators of the project |
Dr. B. Sutradhar bsutra@ndl.gov.in Prof. Saswat Chakrabarti will be added soon |
| 5 | Website/Portal (Helpdesk) | Queries regarding NDLI and its services | support@ndl.gov.in |
| 6 | Contents and Copyright Issues | Queries related to content curation and copyright issues | content@ndl.gov.in |
| 7 | National Digital Library of India Club (NDLI Club) | Queries related to NDLI Club formation, support, user awareness program, seminar/symposium, collaboration, social media, promotion, and outreach | clubsupport@ndl.gov.in |
| 8 | Digital Preservation Centre (DPC) | Assistance with digitizing and archiving copyright-free printed books | dpc@ndl.gov.in |
| 9 | IDR Setup or Support | Queries related to establishment and support of Institutional Digital Repository (IDR) and IDR workshops | idr@ndl.gov.in |
|
Loading...
|