NDLI: A finite element analysis study on different angle correction designs for inclined implants in All-On-Four protocol

Content Provider	Springer Nature : BioMed Central
Author	Ibrahim, Christine Raouf Micheal Sameh, Ahmed Askar, Osama
Abstract	Background The aim of this study is to investigate, through finite element analysis (FEA), the biomechanical behavior of the built-in angle corrected dental implant versus implant with angled multiunit abutment used in All-On-Four treatment protocol. Methods Two (3D) finite element models of a simplified edentulous mandible were constructed with two different posterior implant designs based on the All-On-Four protocol. Four implants were placed in each model, the two anterior implants were positioned vertically at the lateral incisor/canine sites. Depending on the implant fixture design in posterior area, there are two models created; Model I; the mandible was rehabilitated with four co-axis (4 mm in diameter × 15 mm in length) implants with distally built-in angle corrected implants (24-degree angle correction) .While Model II, the mandible was rehabilitated with four conventional (4 mm in diameter × 14 mm in length) implants with a distally inclined posterior implants (25 degree) and angled multiunit abutments. CAD software (Solidworks© 2017; Dassault Systems Solidworks Corp) was used to model the desired geometry. Axial and inclined Loads were applied on the two models. A Finite element analysis study was done using an efficient software ANSYS© with specified materials. The resultant equivalent Von-Misses stresses (VMS), maximum principal stresses and deformation analysis were calculated for each part (implants and prosthetic components). Results When applying axial and non-axial forces, model II (angled multiunit model) showed higher deformation on the level of Ti mesh about 13.286 μm and higher VMS 246.68 MPa than model I (angle corrected implant). Model I exhibited higher maximum stresses 107.83 MPa than Model II 94.988 MPa but the difference was not statistically significant. Conclusion Within the limitation of the FEA study, although angle correcting implant design is showing higher values in maximum principle stresses compared with angled multiunit abutments, model deformation and resultant VMS increased with angled multiunit abutments. The angle correcting designs at implant level have more promising results in terms of deformation and VMS distribution than angle correction at abutment level.
Related Links	https://bmcoralhealth.biomedcentral.com/counter/pdf/10.1186/s12903-024-04091-2.pdf
Ending Page	14
Page Count	14
Starting Page	1
File Format	HTM / HTML
ISSN	14726831
DOI	10.1186/s12903-024-04091-2
Journal	BMC Oral Health
Issue Number	1
Volume Number	24
Language	English
Publisher	BioMed Central
Publisher Date	2024-03-13
Access Restriction	Open
Subject Keyword	Dentistry Oral and Maxillofacial Surgery Angled multiunit abutment Finite element analysis Angle corrected implant
Content Type	Text
Resource Type	Article
Subject	Dentistry
Journal Impact Factor	2.6/2023
5-Year Journal Impact Factor	3.2/2023

Sl.	Authority	Responsibilities	Communication Details
1	Ministry of Education (GoI), Department of Higher Education	Sanctioning Authority	https://www.education.gov.in/ict-initiatives
2	Indian Institute of Technology Kharagpur	Host Institute of the Project: The host institute of the project is responsible for providing infrastructure support and hosting the project	https://www.iitkgp.ac.in
3	National Digital Library of India Office, Indian Institute of Technology Kharagpur	The administrative and infrastructural headquarters of the project	Dr. B. Sutradhar bsutra@ndl.gov.in
4	Project PI / Joint PI	Principal Investigator and Joint Principal Investigators of the project	Dr. B. Sutradhar bsutra@ndl.gov.in Prof. Saswat Chakrabarti will be added soon
5	Website/Portal (Helpdesk)	Queries regarding NDLI and its services	support@ndl.gov.in
6	Contents and Copyright Issues	Queries related to content curation and copyright issues	content@ndl.gov.in
7	National Digital Library of India Club (NDLI Club)	Queries related to NDLI Club formation, support, user awareness program, seminar/symposium, collaboration, social media, promotion, and outreach	clubsupport@ndl.gov.in
8	Digital Preservation Centre (DPC)	Assistance with digitizing and archiving copyright-free printed books	dpc@ndl.gov.in
9	IDR Setup or Support	Queries related to establishment and support of Institutional Digital Repository (IDR) and IDR workshops	idr@ndl.gov.in

Comparison of stresses in monoblock tilted implants and conventional angled multiunit abutment-implant connection systems in the all-on-four procedure

Comparison of stress distribution around all-on-four implants of different angulations and zygoma implants: a 7-model finite element analysis

Evaluation of stress patterns in bone around dental implant for different abutment angulations under axial and oblique loading: A finite element analysis

Finite element analysis on implant-supported bar with different geometric shapes

Static and dynamic stress analysis of different crown materials on a titanium base abutment in an implant-supported single crown: a 3D finite element analysis

Evaluation of Stress Distribution on all-on-four Concept and Conventional Implant Designs: 3D Finite Element Analysis

Evaluation of two treatment concepts of four implants supporting fixed prosthesis in an atrophic maxilla: finite element analysis

Influence of a new abutment design concept on the biomechanics of peri-implant bone, implant components, and microgap formation: a finite element analysis

Effects of different abutment connection designs on the stress distribution around five different implants: a 3-dimensional finite element analysis.

A finite element analysis study on different angle correction designs for inclined implants in All-On-Four protocol

Similar Documents

Comparison of stresses in monoblock tilted implants and conventional angled multiunit abutment-implant connection systems in the all-on-four procedure

Comparison of stress distribution around all-on-four implants of different angulations and zygoma implants: a 7-model finite element analysis

Evaluation of stress patterns in bone around dental implant for different abutment angulations under axial and oblique loading: A finite element analysis

Finite element analysis on implant-supported bar with different geometric shapes

Static and dynamic stress analysis of different crown materials on a titanium base abutment in an implant-supported single crown: a 3D finite element analysis

Evaluation of Stress Distribution on all-on-four Concept and Conventional Implant Designs: 3D Finite Element Analysis

Evaluation of two treatment concepts of four implants supporting fixed prosthesis in an atrophic maxilla: finite element analysis

Influence of a new abutment design concept on the biomechanics of peri-implant bone, implant components, and microgap formation: a finite element analysis

Effects of different abutment connection designs on the stress distribution around five different implants: a 3-dimensional finite element analysis.

A finite element analysis study on different angle correction designs for inclined implants in All-On-Four protocol