NDLI: Effect of iron (Wt.%) on adhesive wear response of Al-12Si-1Cu-0.1Mg alloy in dry sliding conditions

Please wait, while we are loading the content...

Relative performance of alumina coatings prepared by micro arc oxidation and detonation gun spray on AA 6063 under plain fatigue and fretting fatigue loading

Calcium treatment of liquid steel — Assessment of deoxidation constant

Sulphuric acid leaching of polymetallic nodules using paper as a reductant

Metal interlayers to prevent ‘hard zone’ formation in dissimilar weldments of Cr-Mo steels — A comparison between Cu, Co and Ni

Calorimetric studies and kinetic parameters of solid state reactions in 7017 Al-Zn-Mg alloy

Effect of graphite morphology on modulus of elasticity of low carbon equivalent ductile iron

Transactions of the Indian Institute of Metals : Volume 61, Issue 5, October 2008

Transactions of the Indian Institute of Metals : Volume 61, Issue 4, August 2008

Transactions of the Indian Institute of Metals : Volume 61, Issue 2-3, April 2008

Transactions of the Indian Institute of Metals : Volume 61, Issue 1, February 2008

Effect of iron (Wt.%) on adhesive wear response of Al-12Si-1Cu-0.1Mg alloy in dry sliding conditions

Content Provider	Springer Nature Link
Author	Dhiman, Mohit Dwivedi, D. K. Sehgal, Rakesh Bhat, I. K.
Copyright Year	2008
Abstract	The presence of iron leads to different types of intermetallics in Al-Si alloys, among them needle shaped β-phase (Al$_{5}$FeSi) can lead to variations in hardness of the Al-Si alloy which ultimately can affect the wear resistance of the alloy. In this paper, the effect of iron on wear behavior of cast Al-Si alloys has been reported. Sliding wear behavior of eutectic alloy Al-12Si-1Cu-0.1Mg was investigated in dry sliding conditions by using pin-on-disk test configuration against heat treated EN31 steel counter-surface at room temperature. Sliding wear behavior has been evaluated at four normal loads of 5, 20, 50 and 70 N and two sliding speeds, 2 m/s and 4 m/s. Worn pin surfaces were examined by scanning electron microscopy (SEM) for analyzing wear mechanisms. The wear mechanism has been found to be mild oxidative type at lower sliding speed of 2m/s for entire range of loads used in the study. Transition to severe metallic wear occurs at higher sliding speed of 4 m/s at normal load of 5 N. Hardness of the alloy increased with increase in iron addition primarily due to presence of needle shaped Fe-rich intermetallics but it leads to an increased wear rate.
Starting Page	451
Ending Page	456
Page Count	6
File Format	PDF
ISSN	09722815
Journal	Transactions of the Indian Institute of Metals
Volume Number	61
Issue Number	6
e-ISSN	09751645
Language	English
Publisher	Springer-Verlag
Publisher Date	2012-01-28
Publisher Place	India
Access Restriction	One Nation One Subscription (ONOS)
Subject Keyword	Metallic Materials Tribology, Corrosion and Coatings Materials Science
Content Type	Text
Resource Type	Article
Subject	Metals and Alloys

Sl.	Authority	Responsibilities	Communication Details
1	Ministry of Education (GoI), Department of Higher Education	Sanctioning Authority	https://www.education.gov.in/ict-initiatives
2	Indian Institute of Technology Kharagpur	Host Institute of the Project: The host institute of the project is responsible for providing infrastructure support and hosting the project	https://www.iitkgp.ac.in
3	National Digital Library of India Office, Indian Institute of Technology Kharagpur	The administrative and infrastructural headquarters of the project	Dr. B. Sutradhar bsutra@ndl.gov.in
4	Project PI / Joint PI	Principal Investigator and Joint Principal Investigators of the project	Dr. B. Sutradhar bsutra@ndl.gov.in Prof. Saswat Chakrabarti will be added soon
5	Website/Portal (Helpdesk)	Queries regarding NDLI and its services	support@ndl.gov.in
6	Contents and Copyright Issues	Queries related to content curation and copyright issues	content@ndl.gov.in
7	National Digital Library of India Club (NDLI Club)	Queries related to NDLI Club formation, support, user awareness program, seminar/symposium, collaboration, social media, promotion, and outreach	clubsupport@ndl.gov.in
8	Digital Preservation Centre (DPC)	Assistance with digitizing and archiving copyright-free printed books	dpc@ndl.gov.in
9	IDR Setup or Support	Queries related to establishment and support of Institutional Digital Repository (IDR) and IDR workshops	idr@ndl.gov.in

Dry Sliding Wear Behavior of Cold Rolled Spray Cast Al–6Si Alloy

Dry Sliding Wear Behaviour of Ti–6Al–4V Alloy Consisting of Bimodal Microstructure

Roles of Friction-Induced Strain Hardening and Recrystallization in Dry Sliding Wear of AZ31 Magnesium Alloy

Dry Sliding Wear Behavior of Ti–6Al–4V Implant Alloy Subjected to Various Surface Treatments

Dry Sliding and Abrasive Wear Behavior of Nanostructure Zr–W–N Coating

Investigation on the Wear Properties of Primary Si Modified Al–20Si Alloy

Dry sliding wear of microalloyed Er-containing Al–10Sn–4Si–1Cu alloy

Dry Sliding Wear and Corrosion Behaviour of Al-Based Hybrid Composites Reinforced with Micro-Ti$_{p}$ and Micro/Nano-Al$_{2}$O$_{3p}$

Dry Sliding Wear Properties of HVOF Sprayed WC–10Co–4Cr Coating

Effect of iron (Wt.%) on adhesive wear response of Al-12Si-1Cu-0.1Mg alloy in dry sliding conditions

Similar Documents

Dry Sliding Wear Behavior of Cold Rolled Spray Cast Al–6Si Alloy

Dry Sliding Wear Behaviour of Ti–6Al–4V Alloy Consisting of Bimodal Microstructure

Roles of Friction-Induced Strain Hardening and Recrystallization in Dry Sliding Wear of AZ31 Magnesium Alloy

Dry Sliding Wear Behavior of Ti–6Al–4V Implant Alloy Subjected to Various Surface Treatments

Dry Sliding and Abrasive Wear Behavior of Nanostructure Zr–W–N Coating

Investigation on the Wear Properties of Primary Si Modified Al–20Si Alloy

Dry sliding wear of microalloyed Er-containing Al–10Sn–4Si–1Cu alloy

Dry Sliding Wear and Corrosion Behaviour of Al-Based Hybrid Composites Reinforced with Micro-Ti$_{p}$ and Micro/Nano-Al$_{2}$O$_{3p}$

Dry Sliding Wear Properties of HVOF Sprayed WC–10Co–4Cr Coating

Effect of iron (Wt.%) on adhesive wear response of Al-12Si-1Cu-0.1Mg alloy in dry sliding conditions