NDLI: Mechanical Behavior and Microstructure of Electron Beam Melted Ti-6Al-4V Using Digital Image Correlation

Please wait, while we are loading the content...

ANES/ASME Joint National Solar Energy Week

ASME Citrus Engineering Symposium

ASME India Oil and Gas Pipeline Conference

ASME International Mechanical Engineering Congress and Exposition

ASME 2002 International Mechanical Engineering Congress and Exposition(IMECE2002)

ASME 2003 International Mechanical Engineering Congress and Exposition(IMECE2003)

ASME 2004 International Mechanical Engineering Congress and Exposition(IMECE2004)

ASME 2005 International Mechanical Engineering Congress and Exposition(IMECE2005)

ASME 2006 International Mechanical Engineering Congress and Exposition(IMECE2006)

ASME 2007 International Mechanical Engineering Congress and Exposition(IMECE2007)

ASME 2008 International Mechanical Engineering Congress and Exposition(IMECE2008)

ASME 2009 International Mechanical Engineering Congress and Exposition(IMECE2009)

ASME 2010 International Mechanical Engineering Congress and Exposition(IMECE2010)

ASME 2011 International Mechanical Engineering Congress and Exposition(IMECE2011)

ASME 2012 International Mechanical Engineering Congress and Exposition(IMECE2012)

ASME 2013 International Mechanical Engineering Congress and Exposition(IMECE2013)

ASME 2014 International Mechanical Engineering Congress and Exposition(IMECE2014)

ASME 2015 International Mechanical Engineering Congress and Exposition(IMECE2015)

ASME 2016 International Mechanical Engineering Congress and Exposition(IMECE2016)

Volume 7: Fluids Engineering

Volume 4B: Dynamics, Vibration, and Control

Volume 4A: Dynamics, Vibration, and Control

Volume 11: Systems, Design, and Complexity

Volume 10: Micro- and Nano-Systems Engineering and Packaging

Volume 5: Education and Globalization

Volume 9: Mechanics of Solids, Structures and Fluids; NDE, Diagnosis, and Prognosis

Ricochet of High Speed Aluminium Projectiles From a Steel Plate

Evaluate the Importance of Shear Modulus in Dynamic FEM of Flexible Pavement Considering AC Cross-Anisotropy

A Super Singular Element for Three-Dimensional Corner Fronts

Comparing Computational and Experimental Failure of Composites Using XFEM

Can-Crush Model and Simulations for Verifying Uncertainty Quantification Method for Sparse Stress-Strain Curve Data

Analysis of Singular Stress Fields at 3D Piezoelectric Bonded Joints Using a Conservative Integral

Mechanical Properties of Biomimetic Leaf Composite

Effects of Crimped Fiber Paths on Mixed Mode Delamination Behaviors in Woven Fabric Composites

Characterization of Three-Constituent Interface in CNT-Embedded Nanocomposites

Comparison of Load Carrying Capacity of Three and Four Lobed Polygonal Shaft and Hub Connection for Constant Grinding Diameter

A Non-Orthogonal Constitutive Material Model for Advanced Woven Fabrics Based on a Mesoscale Unit Cell

Factors Influencing Blast Attenuation on Walls With Foamed Concrete Boards

CFD Simulation of Highway Contaminant Dispersion

Contact Stiffness Calculation and Effects on Rotordynamic of Rod Fastened Rotor

Dynamic Simulation of Large Flow Solenoid Valve

Simulation of Rotor System Vibrations Using Experimentally Verified Super Elements

Numerical Simulations of Airborne Particle Removal Rates for Air-Ventilated Spaces of Different Obstacle Setups

The Numerical Technique for Turbine Blades and Underplatform Dampers Interaction Modeling Based on Substructure Method

Design of a 4-Cylinder Gasoline Turbo Engine Intake Manifold

Weldment Analysis of a Diesel Engine Exhaust Manifold

Modeling of the Gas-Controlled Crack Growth: Non-Ideal vs Ideal Sink

Comparison of Johnson-Cook Model and an ISV Plasticity Damage Model in Penetration Simulation

Comparisons of Bending Stiffness of 3D Printed Samples of Different Materials

Observations on the Residual Martensite Phase of NiTi Shape Memory Alloy Micro-Tubes Under Uniaxial and Multiaxial Fatigue-Loadings

Deformation and Failure Mechanisms of Austenitic Piping Under the Influence of Oxyhydrogen Reactions

Design Optimisation and Life Estimation of Split Hub Geometry of FSAE Car

Viscoelastic Properties of Carbon/Epoxy Amino-Functionalized Graphene Nanoplatelet Composite

Generic Steel Vehicle Front Bumper and Crush Can Assemblies Subjected to a Rigid High Speed Offset Frontal Impact

Strength Analysis of AL-7F-1 Engine Turbine Rotor Blade

A Method of Predicting Effective Interface Properties of Polymer-Metal Hybrid Structures by Molecular Dynamics

Experimental and Numerical Analysis of the System Ringing in Intermediate Strain Rate Tests

Static Force Analysis of Wheel Bolt Under Multiple Working Conditions

Atomic Diffusion Induced Damage of Ni-Base Super Alloy at Elevated Temperature

Microscopic Analysis of the Initiation of High-Temperature Damage of Ni-Based Heat-Resistant Alloy

A Kinetic Formulation of Reacting Molecular Dynamics

Optical Diagnostics for Energetic Materials Research

Localized Heating due to Stress Concentrations Induced in a Lossy Elastic Medium via the Scattering of Compressional Waves by a Rigid Spherical Inclusion

Modeling the Effects of Texture on Thermal Expansion in Pressed PBX 9502 Components

Experimental Calibration of ISV Damage Model Constants for Pure Copper for High-Speed Impact Simulation

Ring Specimen Geometry for Determining the Ductility of Tubulars

Characterization of Fatigue Crack Propagation Under Complex Biaxial Loading

Variation of the Strength of Grains and Grain Boundaries Caused by the Fluctuation of Their Crystallinity

Void Nucleation and Growth at Grain Boundaries in Copper Bicrystals With Surface Perturbations

Microstructural Analysis of Spall Damage Nucleation and Growth in Multicrystalline Titanium

Characterization of Adhesive Materials Under High Strain Rate Loading

Characterization of Adhesive Joints Under Shock-Wave Loading

The Strength of Dissimilar Fractal Joints

Structural Stress Correction Methods for Linear Elastic Finite Element Analysis of Spot Welded Joints

Stress Corrosion Cracking in Generic Aluminum Foil Under 3.5% NaCl Solution

Large Deformation Strain Measurement Using Digital Image Correlation Technique During Axial Crushing of an Extruded AA-6063 Tube

A Study on Structural Safety Evaluation Technology for Pressing Rings in a Transformer

Investigation of Shock Waves Generated by Electrical Wire Explosion

Evaluation of Dynamic Mechanical Test Methods

Optimizing Fluid Production From Porous Media: From Hydraulic Fractures to Plant Roots

Mechanisms for Kink Band Evolution in Polymer Matrix Composites: A Digital Image Correlation and Finite Element Study

Application of Iso-Strain Boundary Conditions to Deduce Orthotropic Elastic Constants of Biomineralized Fish Scale

The Structure and Mechanical Properties of Aluminum Cellular Metal With Periodic Cubic Cells

Effects of Functionally Graded Cellular Core on Energy Absorption Response of Thin Walled Composite Axial Members

Mechanical Behavior and Microstructure of Electron Beam Melted Ti-6Al-4V Using Digital Image Correlation

Analysis of Fracture Mechanism on Paper Tubes and Relationship Between Paperboard Property and Property of Paper Tubes

Optimal Sinusoidal Cellular Structures for Energy Absorption

On the Effective Properties of 3D Metamaterials

Tailoring Cellular Auxetics for Wearable Applications With Multimaterial 3D Printing

Effect of Raster Orientation on Fracture Toughness Properties of 3D Printed ABS Materials and Structures

Performance of 3-D Printed Thermoplastic Polyurethane Under Quasi-Static and High-Strain Rate Loading

Evaluation of Auxetic Polymeric Structures for Use in Protective Pads

Fatigue Crack Growth Behavior of Hybrid Glass Fiber Laminates With Embedded Functionalized Carbon Nanotube Membranes

Damage Quantification and Location Detection in Carbon Nanotube Enhanced Composite Panels

Processing of Biodegradable Polymer Composite Using Soy Protein-Based Resin and Nanoclay

Fabrication and Characterization of Bio-Based Poly Lactic Acid/Polyhydroxybutyrate-Valerate (PLA/PHBV) Blend With Nanoclay

Identification of Fragments in a Meshfree Peridynamic Simulation

A MOOSE-Based Implicit Peridynamic Thermomechanical Model

Design, Fabrication, and Characterization of a Soft Multi-Fingered Hand

Interconversion of Frequency Domain Complex Modulus to Time Domain Modulus and Compliance of Asphalt Concrete: Numerical Modeling and Laboratory Validation

A New High Strain-Rate Biaxial Experiment to Validate Constitutive Models for Polymers

Integrating First-Principle Calculation and Phase-Field Simulation for Lithium Dendritic Growth on the Anode of a Lithium-Ion Battery

First-Principles Calculations and Molecular Dynamics Simulations on Effect of Hydrogen Impurity in Lead Titanate Films

Micromechanics of Random Heterogeneous Materials: New Background, Opportunities and Prospects

Boundary Value Problems in the Theory of Thermoelasticity for Triple Porosity Materials

Prediction of Hysteresis of a Thermoplastic Polyurethane Using Coarse-Grained Molecular Dynamics

Fatigue of Coiled Tubing and its Influencing Factors: A Comparative Study

Finite Element Simulation of PZT-Aided Interrogation of Composite Laminates Exhibiting Damage

Characterization of Interlaminar Fracture Properties of Advanced Polymer Matrix Composites Interleaved With Buckypaper

Mechanical Strength Responses of Poled Lead Zirconate Titanate Under Extreme Electric Field and Various Temperature Conditions

Computational Modeling of Anterior and Posterior Pelvic Organ Prolapse (POP)

Finite Element Analysis of a Curing Press With Focus on Tightness of the Vulcanizing Chamber

A Coupled Temperature-Displacement Numerical Analysis of Hydraulic Press Workspace

An Experimental Investigation of Industrial Gearbox Condition Using Wear Particle Analysis Technique

Compressed Sensing Techniques for Ultrasonic Imaging of Cargo Containers

Piezoelectric-Based Viscosity Probe for Early-Age Concrete Curing Process Monitoring

The Effects of Carbon Fiber Misalignment on Material Composite Strength

Modeling of Lamb Wave Propagation in Beam-Like Structures via Wavelet Finite Element Method

Fully Coupled Numerical Simulation for Wave Propagation in Composite Materials

A Novel Ultrasonic Technique for the Detection of Distributed Precursor Damages in Composites

Guided Waves in a Plate With a Delamination-Like Discontinuity

Efficient Modeling of Nonlinear Scattering of Ultrasonic Guided Waves From Fatigue Cracks Using Local Interaction Simulation Approach

Characterization of Materials Fabricated by Additive Manufacturing Method Using Line Focused Ultrasonic Transducer

Selection of Vibro-Characteristics for Monitoring Flange Integrity in the Field Conditions

Wireless Interrogation of a High Temperature Antenna Sensor Without Electronics

Electro-Mechanical Impedance Measurements in an Imitated Low Earth Orbit Radiation Environment

Volume 14: Emerging Technologies; Materials: Genetics to Structures; Safety Engineering and Risk Analysis

Volume 2: Advanced Manufacturing

Volume 3: Biomedical and Biotechnology Engineering

Volume 6B: Energy

ASME 2017 International Mechanical Engineering Congress and Exposition(IMECE2017)

ASME 2018 International Mechanical Engineering Congress and Exposition(IMECE2018)

ASME International Pipeline Geotechnical Conference

ASME Power Conference

ASME Turbine Blade Tip Symposium

ASME/IEEE Joint Rail Conference

ASME/JSME Thermal Engineering Joint Conference

ASME/NRC Pump and Valve Symposium

ASME/USCG Workshop on Marine Technology and Standards

CANEUS: MNT for Aerospace Applications

Dynamic Systems and Control Conference

Energy Nanotechnology International Conference

Energy Sustainability

Engineering Systems Design and Analysis

Engineering Technology Conference on Energy

Fluid Power Systems Technology

Fluids Engineering Division Summer Meeting

Frontiers in Biomedical Devices

Gas Turbine India Conference

Global Congress on NanoEngineering for Medicine and Biology

Heat Transfer Summer Conference

High Temperature Reactor Technology

Information Storage and Processing Systems

Integrated Nanosystems: Design, Synthesis, and Applications

Internal Combustion Engine Division Fall Technical Conference

Internal Combustion Engine Division Spring Technical Conference

International Conference on Fluidized Bed Combustion

International Conference on Fuel Cell Science, Engineering and Technology

International Conference on Integration and Commercialization of Micro and Nanosystems

International Conference on Micro/Nanoscale Heat Transfer

International Conference on Nanochannels, Microchannels, and Minichannels

International Conference on Nuclear Engineering

International Conference on Offshore Mechanics and Arctic Engineering

International Conference on Radioactive Waste Management and Environmental Remediation

International Design Engineering Technical Conferences and Computers and Information in Engineering Conference

International Electronic Packaging Technical Conference and Exhibition

International Heat Transfer Conference

International Joint Power Generation Conference

International Joint Tribology Conference

International Manufacturing Science and Engineering Conference

International Pipeline Conference

International Solar Energy Conference

International Symposium on Flexible Automation

Multifunctional Nanocomposites and Nanomaterials International Conference

Noise Control and Acoustics Division Conference

North American Waste-to-Energy Conference

Pressure Technology

Pressure Vessels and Piping Conference

Rail Transportation Division Conference

Small Modular Reactors Symposium

Smart Materials, Adaptive Structures and Intelligent Systems

Summer Bioengineering Conference

Turbo Expo: Power for Land, Sea, and Air

Verification and Validation

Water Quality, Drought, Human Health and Engineering Conference

Wind Energy Symposium

World Conference on Innovative Virtual Reality

World Tribology Congress

Mechanical Behavior and Microstructure of Electron Beam Melted Ti-6Al-4V Using Digital Image Correlation

Content Provider	The American Society of Mechanical Engineers (ASME) Digital Collection
Author	Haque, Mohammad Shafinul Arrieta, Edel Mireles, Jorge Carrasco, Cesar Calvin, M. Stewart Ryan, B. Wicker
Copyright Year	2016
Abstract	The reputation of additive manufacturing technology has increased dramatically in recent years due to its freedom of design, customization, and waste minimization. The growing demand for complex profile components to achieve more economic and strength-to-weight efficient aero-engine components can be met by additive manufacturing technology. In this study, electron beam melting (EBM), a powder bed additive layer manufacturing process, is used to manufacture Ti-6Al-4V tensile specimens. The Ti-6AL-4V alloy has excellent corrosion and high temperature resistance with a high strength-to-weight ratio. It is widely used in the power generation, aerospace, and medical industries. An Arcam Ti-6Al-4V prealloyed powder with particle sizes ranging from 45μ–100μ is used in an Arcam A2 machine to manufacture three specimens at zero degree manufacturing orientation. The zero degree manufacturing orientation is expected to exhibit a higher strength over other orientations. The EBM manufacturing parameters were set at 15mA current and 4530 mm/sec beam speed. Tensile tests were performed at room temperature (25.5°C) under a strain rate of 0.003 mm/mm/min according to the ASTM E8 standard for strain-rate sensitive materials. Stress-strain curves are plotted and discussed. Tensile test results indicate a tensile strength of 1.2 GPa and an elongation of 8% approximately. Three Dimensional Digital Image Correlation (3D-DIC) is used to measure the full strain field and deformation evolution on the surface of the specimens. The 3D-DIC system compares digital photographs (taken at two different angles simultaneously) of the surface of a specimen and calculates the deformation and strain fields. Using the strain fields the mechanical properties are determined by the relationships in the strain tensor. The tensile test results show that for a zero degree manufacturing orientation, the yield strength (YS) and ultimate tensile strength (UTS) are higher than that typically reported for wrought products. Fractography using optical microscopy (OM) and Scanning Electron Microscopy (SEM) were conducted. Micrographs of transverse section of the specimen were obtained to identify and analyze the failure mechanism that took place during testing. The built direction, presence of voids, manufacturing defects, and unmelted particles are observed from the SEM views. Surface roughness and microstructure were observed in the OM. A comparison of the obtained results with the literature for additively manufactured Ti-6Al-4V and possible causes are discussed.
File Format	PDF
ISBN	9780791850633
DOI	10.1115/IMECE2016-66178
Volume Number	Volume 9: Mechanics of Solids, Structures and Fluids; NDE, Diagnosis, and Prognosis
Conference Proceedings	ASME 2016 International Mechanical Engineering Congress and Exposition
Language	English
Publisher Date	2016-11-11
Publisher Place	Phoenix, Arizona, USA
Access Restriction	Subscribed
Subject Keyword	Temperature Deformation Stress-strain curves Additive manufacturing Aircraft engines High temperature Machinery Aerospace industry Cathode ray oscilloscopes Astm international Design Optical microscopy Electron beams Weight (mass) Energy generation Manufacturing Elongation Failure mechanisms Testing Waste reduction Scanning electron microscopy Mechanical behavior Melting Alloys Mechanical properties Surface roughness Tensile strength Tensors Biomedicine Corrosion Particulate matter Yield strength Fractography
Content Type	Text
Resource Type	Article

Central Library (ISO-9001:2015 Certified)
Indian Institute of Technology Kharagpur
Kharagpur, West Bengal, India | PIN - 721302

See location in the Map
03222 282435
Mail: support@ndl.gov.in

Sl.	Authority	Responsibilities	Communication Details
1	Ministry of Education (GoI), Department of Higher Education	Sanctioning Authority	https://www.education.gov.in/ict-initiatives
2	Indian Institute of Technology Kharagpur	Host Institute of the Project: The host institute of the project is responsible for providing infrastructure support and hosting the project	https://www.iitkgp.ac.in
3	National Digital Library of India Office, Indian Institute of Technology Kharagpur	The administrative and infrastructural headquarters of the project	Dr. B. Sutradhar bsutra@ndl.gov.in
4	Project PI / Joint PI	Principal Investigator and Joint Principal Investigators of the project	Dr. B. Sutradhar bsutra@ndl.gov.in Prof. Saswat Chakrabarti will be added soon
5	Website/Portal (Helpdesk)	Queries regarding NDLI and its services	support@ndl.gov.in
6	Contents and Copyright Issues	Queries related to content curation and copyright issues	content@ndl.gov.in
7	National Digital Library of India Club (NDLI Club)	Queries related to NDLI Club formation, support, user awareness program, seminar/symposium, collaboration, social media, promotion, and outreach	clubsupport@ndl.gov.in
8	Digital Preservation Centre (DPC)	Assistance with digitizing and archiving copyright-free printed books	dpc@ndl.gov.in
9	IDR Setup or Support	Queries related to establishment and support of Institutional Digital Repository (IDR) and IDR workshops	idr@ndl.gov.in